The ISCOM S2600(-PWR/PWH) series switches are the new-generation green and cost-effective Layer 2 Gigabit Ethernet switches, providing flexible 1000Mbps access interfaces and 10Gbps uplink interface. It is developed based on a high-performance hardware platform and the new-generation switching software platform of Raisecom.
Featuring high reliability, high access security guarantee, easy administration, and simple management, it can meet carriers' requirements. In addition, it supports IPv4/v6 static route, mature IPv6 features, intelligent virtualization technologies, flexible PoE, and so on. It can be widely used in scenarios such as access device of enterprises, campuses, residences, and CDN.
High capacity, high density
High reliability and protection
• STP, RSTP, MSTP
• Manual and static LACP
• ITU-T G.8031 line protection and G.8032 ring protection
• Dual-system and dual-configuration-file redundancy backup
ISF Stacking
• Up to 4 devices
• Linear and ring stacking
• Uplink connect
Complete security guarantees
• Various AAA mode such as RADIUS and TACACS+
• IEEE 802.1x authentication, MAC authentication, and bypass authentication
• Port secure MAC and limits on the MAC addresses to stop attacks from illegal users
• Dynamic ARP inspection, ARP rate limit
• Various ACL policies to control packet forwarding lexibly
• DHCPv4/v6 Snooping and Option 82/18/37 to avoid DHCP attacks
• DAI and IP Source Guard based on the DHCP binding table to prevent ARP looding attacks and IP attacks
• Broadcast storm and loop detection to ensure the stability of the network
• Lightning protection for the power supply and all the Ethernet electric interfaces and protect hardware investment of the customer Fine tunable QoS
• Rich scheduling policy such as SP, WRR, or SP+WRR, DRR, or SP+DRR
• Dual-bucket three-color CAR based on the traffic and H-CAR
• Statistics based on traffic
Mature IPv6 technology
• IPv6 PING/TELNET/SSH/FTP/SNMP/HTTP management
• IPv6 Source Guard, IPv6 prefix Snooping
• VRRPv3, IPv6 routing, and IPv6 Path MTU
Smart PoE
• IEEE802.3af/IEEE802.3at/IEEE802.3bt standard
• PD alive-check
• Configuring reboot the PD at a specific time
• Supplying power during specified time interval
Advanced management system
• SNMP, RMON, Telnet, SSH and provide friendly WEB management interface to increase the usability of the device
• Automatic configuration and loading. The administrator can put the configuration file set in advance to the TFTP server for the automatic loading of the switch while it is booting, thus simplifying the management and maintenance
• Raisecom USB automatic deployment. Simply insert the USB lash disk to easily upgrade, configure, and deploy the device
|
P/N |
ISCOM S2600-8T4X(-PWR) |
ISCOM S2600-8S4T4X |
ISCOM S2600-24T4X(-PWR/PWH) |
|
Port type |
Uplink: 4 x GE/10G SFP+ Downlink: 8 x GE RJ45 |
Uplink: 4 x GE RJ45 + 4 x GE/10G SFP+ Downlink: 8 x GE SFP |
Uplink: 4 x GE/10G SFP+ Downlink: 24 x GE RJ45 |
|
Management interface |
1 Console interface, 1 SNMP out-of-band interface, and 1 USB interface (except the S2600-8S4T4X) |
||
|
Switching capacity |
96Gbit/s |
104Gbit/s |
128Gbit/s |
|
Packets switch rate |
71Mpps |
77Mpps |
95Mpps |
|
Dimension(mm) |
260(L) × 130(W) × 43.6(H) PoE: 300(L) × 220(W) × 43.6(H) |
220(L) × 230(W) × 43.6(H) |
440(L) × 220(W) × 43.6(H) PoE: 440(L) × 300(W) × 43.6(H) |
|
Max Power consumption |
13w PoE: 150w(AC), 260w(DC) |
35w |
24w PoE: 575w(AC), 840w(DC) |
|
Power supply |
Embedded with single power supply: AC, DC (for ISCOM S2600-24T4X-PWR/PWH, single/dual power supplies: AC/S, AC/D, DC/D, and AC_DC) |
||
|
P/N |
ISCOM S2600-8T4S |
ISCOM S2600-24T4S |
ISCOM S2600-24S4X |
|
Port type |
Uplink: 4 x GE SFP Downlink: 8 x GE RJ45 |
Uplink: 4 x GE SFP Downlink: 24 x GE RJ45 |
Uplink:4 x GE/10G SFP+ Downlink: 24 x GE SFP |
|
Management interface |
1 Console interface, 1 SNMP out-of-band interface, and 1 USB interface |
||
|
Switching capacity |
24Gbit/s |
56Gbit/s |
128Gbit/s |
|
Packets switch rate |
18Mpps |
42Mpps |
95Mpps |
|
Dimension(mm) |
260(L) × 130(W) × 43.6(H) |
440(L) × 220(W) × 43.6(H) |
440(L) × 300(W) × 43.6(H) |
|
Max Power consumption |
13w |
24w |
43w |
|
Power Supply |
Embedded with single power supply: AC, DC |
Embedded with single/dual power supplies: AC/S, DC/S, AC/D, DC/D, and AC_DC |
|
|
Hardware |
Working temperature: -10 to 55ºC Relevant humidity: 5%–90% RH (non-condensing) Voltage range: AC 220V(100~240V), DC 48V(-36~-72V) PoE: AC 100–240 V, DC 45–57 V Note: 45–57 VDC IEEE802.3af 51–57 VDC IEEE802.3at 53–57 VDC IEEE802.3bt anti-thunder (cable port): CM 4kV |
||
|
L2 |
Jumbo frame up to 12K bytes Support VLAN based on MAC/protocol/IP subnet/interface. Support 4K VLANs, QinQ and VLAN mapping(1:1/N:1) Support 16K MAC address |
||
|
Multicast |
IGMP snooping, MLD snooping, IGMP MVR, IGMP/MLD filter, IGMP/MLD proxy |
||
|
QoS/ACL |
Support rate limiting based on the ingress direction and egress direction of interfaces. Support HCAR Each interface supports 8 queues and priority mapping Support traffic classification and traffic policy Support SP, WRR, DRR, SP+WRR, and SP+DRR queue scheduling modes Support congestion control WRED Support interface/queue shaping |
||
|
Reliability |
Support manual aggregation and static LACP Support ERPS (ITU-T G.8032) Support STP/RSTP/MSTP and spanning tree protection functions: BPDU Guard, root Guard, loop protection, TC protection/suppression Support Loop Detection Protection (LBD) |
||
|
Security |
Support AAA mode such as Tacacs+, radius; 802.1x authentication, MAC address authentication, and bypass authentication. Support Guest VLAN and Voice VLAN Support the whitelist, port security MAC, and MAC address limit Support IP attack prevent and ARP attack prevention: IPv4/v6 Source Guard and IPv6 prefix Snooping; DAI and ND Snooping Support SSHv2.0, CPU protection |
||
|
DHCP |
DHCPv4/v6 client/server/snooping/relay DHCPv4 option61/82 DHCPv6 option18/37 |
||
|
IPv6 |
Support dual stacks Support IPv6 Ping/Tracert/Telnet/ SSH, IPV6 FTP/TFTP/SFTP Support IPV6 RADIUS, IPV6 TACACS+, IPV6 NTP, and SNTP Support ND, IPv6 Path MTU, VRRPv3 |
||
|
IP Routing |
IPv4 and IPv6 static route Support ECMP and policy routing |
||
|
Management and maintenance |
Support diversified management methods (CLI, SNMPv1/v2c/v3, Web network management, Telnet, and SSHv2.0) Support the Raisecom RCView system Support local and remote port mirroring, traffic mirroring Support system logs and hierarchical alarms. Support power Dying Gasp. Support optical module DDM, Virtual Cable Test (VCT) and UDLD. Support IPv4/v6 ZTP Support system and environment monitoring (CPU/Memory/Flash/Temperature/power/fan) |
||
|
Clock-sync |
NTPv4/v6, PTP-TC |
||
|
POE (for PoE switches only) |
Support mandatory power supply mode for non-standard PDs Support PoE power management, including enabling/disabling interface power supply, interface output power configuration, power supply priority configuration, power overload protection, and overtemperature protection Support timed power supply for POE, timed restarting PDs, monitoring PD connectivity status, and restarting PD upon loss of connection |
||
